Skip to content

Dasharo Compatibility: M.2 WiFi/Bluetooth

Test cases

Common

Test setup

  1. Proceed with the Generic test setup: firmware
  2. Proceed with the Generic test setup: OS installer
  3. Proceed with the Generic test setup: OS installation
  4. Proceed with the Generic test setup: OS boot from disk

WLE001.001 Wireless card detection (Ubuntu 20.04)

Test description

This test aims to verify that the Wi-Fi/Bluetooth card is enumerated correctly and can be detected from the operating system

Test configuration data

  1. FIRMWARE = coreboot
  2. OPERATING_SYSTEM = Ubuntu 20.04

Test setup

  1. Proceed with the Common section.

Test steps

  1. Open a terminal window and execute the following command:
    lspci | grep AX20
    

Expected result

The output of the command should contain the line:

    2f:00.0 Network controller: Intel Corporation Wi-Fi 6 AX200 (rev 1a)

The exact name and revision may be different depending on hardware configuration.

WLE001.002 Wireless card detection (Windows 10)

Test description

This test aims to verify that the Wi-Fi/Bluetooth card is enumerated correctly and can be detected from the operating system

Test configuration data

  1. FIRMWARE = coreboot
  2. OPERATING_SYSTEM = Windows 10

Test setup

  1. Proceed with the Common section.

Test steps

  1. Open PowerShell and execute following command: Get-PnpDevice -PresentOnly | Select-String -Pattern "Wi-Fi"
  2. Note the result

Expected result

The output of the command should contain a line starting with:

    Intel(R) Wi-Fi 6AX200 160MHz

or a line starting with

    Intel(R) Wi-Fi 6AX201 160MHz

WLE002.001 Wi-Fi scanning (Ubuntu 20.04)

Test description

This test aims to verify that the Wi-Fi functionality of card is initialized correctly and can be used from within the operating system.

Test configuration data

  1. FIRMWARE = coreboot
  2. OPERATING_SYSTEM = Ubuntu 20.04

Test setup

  1. Proceed with the Common section.
  2. Make sure to have any Wi-Fi signal available

Test steps

  1. Open a terminal window and execute the following commands as root:
    nmcli radio wifi on
    nmcli device wifi rescan
    # Wait ~5 seconds
    nmcli device wifi list
    

Expected result

The output of the last command should return a list of available Wi-Fi networks, for example:

IN-USE  BSSID              SSID                    MODE   CHAN  RATE        SIGNAL  BARS  SECURITY
        36:78:EE:05:03:45  DIRECT-ny               Infra  6     65 Mbit/s   75      ▂▄▆_  WPA2
*       60:38:E0:D6:46:9A  3mdeb_abr_5GHz          Infra  48    405 Mbit/s  72      ▂▄▆_  WPA2
        60:38:E0:D6:46:99  3mdeb_abr               Infra  11    54 Mbit/s   69      ▂▄▆_  WPA2
        D8:D7:75:02:F9:BF  FunBox2-F9BF_2.4GHz     Infra  1     130 Mbit/s  50      ▂▄__  WPA1 WPA2
        30:5A:3A:A1:46:B0  H_Office                Infra  2     270 Mbit/s  35      ▂▄__  WPA2
        9E:93:4E:74:C0:3F  DIRECT-xpPhaser 3330    Infra  1     65 Mbit/s   34      ▂▄__  WPA2
        D8:A7:56:D9:A7:9F  Orange_Swiatlowod_A79A  Infra  108   540 Mbit/s  32      ▂▄__  WPA2
        86:25:19:05:D4:A0  DIRECT-KRM288x Series   Infra  11    54 Mbit/s   22      ▂___  WPA2
        D8:A7:56:D9:A7:9A  Orange_Swiatlowod_A79A  Infra  11    130 Mbit/s  20      ▂___  WPA2
        9E:93:4E:74:C0:57  DIRECT-ejPhaser 3330    Infra  1     65 Mbit/s   17      ▂___  WPA2
        B0:BE:76:06:9F:22  NED-WIFI                Infra  11    270 Mbit/s  17      ▂___  WPA2

WLE002.002 Wi-Fi scanning (Windows 10)

Test description

This test aims to verify that the Wi-Fi functionality of card is initialized correctly and can be used from within the operating system.

Test configuration data

  1. FIRMWARE = coreboot
  2. OPERATING_SYSTEM = Windows 10

Test setup

  1. Proceed with the Common section.
  2. Make sure to have any Wi-Fi signal available

Test steps

  1. Locate in the bottom right corner of the screen Internet access icon and click it
  2. Enable Wi-Fi and note the result.

Expected result

After enabling Wi-Fi available networks should appear in the Internet access menu

WLE003.001 Bluetooth scanning (Ubuntu 20.04)

Test description

This test aims to verify that the Bluetooth functionality of card is initialized correctly and can be used from within the operating system.

Test configuration data

  1. FIRMWARE = coreboot
  2. OPERATING_SYSTEM = Ubuntu 20.04

Test setup

  1. Proceed with the Common section.
  2. Enable Bluetooth and make it discoverable in any device nearby DUT

Test steps

  1. Open a terminal window and execute the following commands:
    bluetoothctl
    power on
    scan on
    # Wait ~5 seconds
    devices
    

Expected result

The output of the last command should return a list of detectable Bluetooth devices, for example:

Device 48:24:57:E0:61:74 48-24-57-E0-61-74
Device 88:BD:45:74:FA:A5 Wojtek N
Device CE:9E:7B:BF:69:F2 Mi Smart Band 4
Device 56:62:93:8B:1A:F9 Galaxy Watch4 Classic (PHLM)
Device 64:F2:FD:1E:26:BC Galaxy Watch4 Classic (PHLM)
Device 0F:18:A1:D9:23:F6 0F-18-A1-D9-23-F6
Device 8C:EA:48:B1:59:B3 [Signage] Samsung QMR Series
Device 8C:EA:48:B1:57:EB [Signage] Samsung QMR Series
Device 76:C7:FD:86:9B:0E 76-C7-FD-86-9B-0E
Device 40:5E:96:43:3A:6A 40-5E-96-43-3A-6A
Device 4C:58:3B:C1:37:90 4C-58-3B-C1-37-90
Device 6A:93:A2:6A:E5:20 6A-93-A2-6A-E5-20

WLE003.002 Bluetooth scanning (Windows 10)

Test description

This test aims to verify that the Bluetooth functionality of card is initialized correctly and can be used from within the operating system.

Test configuration data

  1. FIRMWARE = coreboot
  2. OPERATING_SYSTEM = Windows 10

Test setup

  1. Proceed with the Common section.
  2. Enable Bluetooth and make it discoverable in any device nearby DUT

Test steps

  1. Enter Notification Center in the bottom right part of the screen
  2. Using right mouse button click on the Bluetooth icon
  3. In shown drop-down menu click Go to settings
  4. Click the + icon described as Add Bluetooth or other device
  5. In the Add a device menu click Bluetooth
  6. Wait a few moments until DUT scans for nearby Bluetooth devices and note the result

Expected result

Available Bluetooth devices should appear in the Add a device window.